FIBARO FGR-222 module automation system for rolling shutter Z-Wave Plus DIN-rail

Pack module, Fibaro Z-Wave Plus FGR-222 with mounting bracket DIN-rail Eutonomy R222.

FGR-222 module Z-Wave device from Fibaro , which allows control of any installation with an ac motor.It also allows a control by wall switch.

The module Z-Wave of Fibaro FGR-222 allows precision control of the mechanical engines, as well as the end of the race of all system, in particular, the motion systems at the end of the race electronics.

This module works with the neutral!

The module FGR-222 is capable of transmitting the power consumption instant (W) and cumulative (KWh) of

Features:

• Order your blinds or shutters remotely

• Compatible with OSI and venetian blind with positioning of the slats

• Installs behind existing switch

• According to ascent/descent and positioning

• Compatible with the motors to stop mechanical or electronic

• Terminal blocks for greater wiring convenience

• Rounded shape to meet the most stringent standards

• Measurement of the instantaneous fuel consumption, and cumulative

• Wireless update with the box, Fibaro Home Center 2

• Function test coverage Z-Wave network

• Small, discrete and aesthetic

• Ease of use and installation

• Type of module : Receiver Z-Wave

• Power supply : 110 - 240V~, 50/60Hz

• Power consumption : < 0.8 W

• Wiring : 3-wire, neutral required

• Max load :

  • 4.2 A for resistive loads

  • 1.7 A for motors with compensated power factor (inductive loads)

• Frequency : 868,42 Mhz

• Signal power : 1mW

• Transmission Distance : 50m free field, 30 m indoors

• Dimensions: 20 x 42 x 38 mm

• Operating temperature : 0-40°C

• Temperature limit : 105°C

• Standards :

  • RoHS 2011/65/EU

  • LVD 2006/95/EC

  • EMC DIRECTIVE 2004/108/EC

  • R&TTE DIRECTIVE 1999/5/EC

The adapter Eutonomy euFIX R222 is used to install the module Fibaro® Switch FGR-222 or FGRM-222 on a rail of type DIN TH35 in the electrical panel.

The adapter Eutonomy euFIX R222 consists of a housing and an electronic card, on which the Switch module FGR-222 or FGRM-222 is mounted.

The dimensions of the case are appropriate for a standard rail DIN TH35/TS35.

The e-card contains a set of screw terminals, where all the wires (power, signal input and output, command buttons) can be connected safely.

The front panel of the case contains two micro-buttons of diagnosis S1 and S2, which can be used to control the module, save the module in the Z-Wave system or remove it from the system without opening the housing of the adapter.

Features R222:

• Adapter DIN to Fibaro Switch FGR-222 or FGRM-222 without push buttons

• Used to install the module Fibaro Switch FGR-222 or FGRM-222 on the din rail of type DIN-TH35 / TS35 in the electrical panel

• Location free on the label to identify the line controlled

• Supply voltage: 230 V AC +/- 10%, 50-60Hz

• Power load: max 6.5 A per channel, 10A total

• Dimensions: 34,8 x 87,3 x 64,7 mm

• Width in units TE: 2 TE coolers

• Cross Section of the conductor of wire : max. 2.5 mm2

• Maximum length of the wires connected to the inputs Sx, S1, S2: 20m

• Operating temperature: 0 ° C to +50 ° C

• Relative humidity: ≤90%, no condensation

• Guidelines:

  • LVD 2014/35 / EC

  • RoHS 2011/65 / EU