FIBARO FGS-222 - Module switch double Z-Wave and More with support for DIN rail
search
  • FIBARO FGS-222 - Module switch double Z-Wave and More with support for DIN rail

FIBARO FGS-222 - Module switch double Z-Wave and More with support for DIN rail

€73.49
VAT included

Module Fibaro FGS-222 Z-Wave and More with support for DIN rail

Quantity
In the course of resupplying

  Garanties sécurité

(à modifier dans le module "Réassurance")

  Politique de livraison

(à modifier dans le module "Réassurance")

  Politique retours

(à modifier dans le module "Réassurance")

Module Fibaro FGS-222 Z-Wave and More with support for DIN rail

Pack module, Fibaro Z-Wave More FGS-222 with mounting bracket DIN-rail Eutonomy S222NP

FGS-222 micro-module Z-WAVE FIBARO can connect behind a double switch.

The micro-module FGS-222 works as an ON/OFF switch.

The micro-module FGS-222 has two relay potential-free.

Therefore, you can control any voltage, or order a garage door,a boiler,a radiator, by simple contact.

The micro-module FGS-222 has terminal block greater allowing the connection of two cables of 1.5 mm2.

Characteristics of the micro module, FIBARO FGS-222:

  • Type of module : Receiver Z-Wave

  • Power supply : 110 - 240V~, 50/60Hz

  • Power Consumption : 0.8 W

  • Wiring : 3-wire, neutral required

  • Current maximum per output : 6.5 A / 110 - 240V~, 50/60Hz

  • Current max total : 10A / 110 - 240V~, 50/60Hz

  • Frequency : 868,42 Mhz

  • Transmission Distance : 50m free field, 30 m indoors

  • Signal power : 1mW

  • Dimensions: 15 x 42 x 38 mm

  • Operating temperature : 0-35°C

  • Temperature limit : 105°C

  • Standards :

    • RoHS 2011/65/EU

    • LVD 2006/95/EC

    • EMC DIRECTIVE 2004/108/EC

    • R&TTE DIRECTIVE 1999/5/EC

The adapter Eutonomy euFIX S222NP is used to install the module Fibaro® Switch FGS-222 on a rail of type DIN TH35 in the electrical panel.

The adapter Eutonomy euFIX S222NP consists of a housing and an electronic card on which the module Switch FGS-222 is mounted.

The dimensions of the case are appropriate for a standard rail DIN TH35/TS35.

The e-card contains a set of screw terminals, where all the wires (power, signal input and output, command buttons) can be connected safely.

Features S222NP:

  • Adapter DIN to Fibaro Switch FGS-222 without push buttons

  • Used to install the module Fibaro Switch FGS-222-rail type DIN-TH35 / TS35 in the electrical panel

  • Location free on the label to identify the line controlled

  • Supply voltage: 230 V AC +/- 10%, 50-60Hz

  • Power load: max 6.5 A per channel, 10A total

  • Dimensions: 34,8 x 87,3 x 64,7 mm

  • Width in units TE: 2 TE coolers

  • Cross Section of the conductor of wire : max. 2.5 mm2

  • Maximum length of the wires connected to the inputs Sx, S1, S2: 20m

  • Operating temperature: 0 ° C to +50 ° C

  • Relative humidity: ≤90%, no condensation

  • Guidelines:

    • LVD 2014/35 / EC

    • RoHS 2011/65 / EU

 

FGS-222-S222NP

Data sheet

Protocol
Z-WAVE
Functions
Actuator

Specific References

chat Comments (0)
No customer reviews for the moment.