- On sale!
- -10%
USB controller AEON LABS...
Z_Stick PC-Adapter Z-WAVE AEON LABS to turn a PC into a Z-WAVE controller.
Adequacy with many software.
(à modifier dans le module "Réassurance")
(à modifier dans le module "Réassurance")
(à modifier dans le module "Réassurance")
ODROID C4 is a next-generation single-board computer that is more energy efficient and capable than ODROID C2, which was introduced more than four years ago as the world's first affordable 64-bit ARM computer.
The ODROID C4's main processor is built with a quad-core Cortex-A55 cluster with a next-generation Mali-G31 GPU.
A55 cores operate at 2.0GHz without thermal throttling using the original heatsink for a rugged and quiet computer.
Multi-core CPU performance is approximately 40% faster and system DRAM performance is 50% faster than ODROID C2.
Card dimensions: 85 mm x 56 mm x 1.0 mm
Heatsink dimensions: 40 mm x 32 mm x 10 mm
Weight: 59 g with heatsink
Amlogic S905X3 12nm Processor
L1 instruction cache: 32 KB, 4-port associative set (128 sets), 64-byte rows, shared by 1 processor
L1 data cache: 32 KB, 4-port associative set (128 sets), 64-byte rows, shared by 1 processor
L3 data cache: 512 KB, 16-port associative set (512 sets), 64-byte rows, shared by 4 processors
Quad-Core Cortex-A55 (2.016GHz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G31 MP2 GPU with 4 execution engines (650Mhz)
4GB DDR4 memory with 32-bit bus width
Data rate: 2640 MT/s (grade PC4-21333)
Low-power design of 1.2 volts
Storage 1x eMMC connector (8/16/32/64GiB are available)
1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
Realtek RTL8211F (Ethernet transceiver)
LED indicators
Green LED: Flashing by data traffic at a 100 Mbps connection
Orange LED: Flashing when data traffic at 1,000 Mbps connection
Optional USB Wi-Fi adapters
1 x HDMI 2.0 video (up to 4K@60Hz with HDR, CEC, EDID)
Audio 1 HDMI digital output
1 x Optional SPDIF optical output
External I/O 4 USB 3.0 host ports (sharing a single root hub)
1 USB 2.0 OTG port for host or device mode. (No power input)
1 x Serial Debug Console (UART)
1 x Peripheral expansion connector (40-pin, 2.54mm pitch)
2x DC 5V, 2x DC 3.3V, 1x DC 1.8V, 8x GND
1x SPI
1x UART
2x I2C
6x PWM
2x ADC input (12bit, 1.8V Max)
25x GPIO (maximum)
1x Audio expansion connector (7-pin, 2.54mm pitch)
1x DC 5V
1 SPDIF output
1x I2S
All 3.3V I/O signal levels, except for ADC input at 1.8 Volt max.
Other Features IR receiver for remote control
System LED indicators:
Red (PWR) – Turned on when DC power is connected
ALIVE - Blinking like a heartbeat while the kernel is running.
Power supply 1 x DC socket: outer diameter (negative) 5.5 mm, inner diameter (positive) 2.1 mm
DC input: 5.5V ~ 13V (*15V/4A power supply is not compatible with C4)
A DC 12V/2A AC adapter is recommended
Power consumption:
IDLE: ≃ 1.8W
CPU stress: ≃ 3.64W (Performance Governor)
Power off: ≃ 0.14W