Fibaro FGS-223 - Fibaro module double switch Z-Wave Plus DIN-rail



New product

Fibaro FGS-223 module Z-Wave Plus DIN-rail

More details

By buying this product you can collect up to 8 loyalty points. Your cart will total 8 loyalty points that can be converted into a voucher of 1,36 €.

89,99 € tax incl.

Instead of 131,94 €

More info

Fibaro FGS-223 module Z-Wave Plus DIN-rail

Pack module Fibaro FGS-223 Z-Wave and more with support for DIN rail Eutonomy S223

FGS-223 micro-module Z-WAVE MORE FIBARO allows you to control electrical devices in switching mode and can connect behind an existing switch.

Attention, this module requires the neutral to work. The output is not potential-free, it does not control a dry contact or a load having a different supply voltage than the input.

The micro-module FGS-223 functions as ON/OFF switch.

The micro-module FGS 223 has the function of measurement of power and energy to control your consumption.

The module Z-wave More FGS-223 has a terminal block to wire the cables of high section.

The module Z-wave More FGS-223 has a status LED to verify the inclusion, the strength of the signal,the update of the module.

You can manage the software of the module FGS-223.

 The module Z-wave More FGS-223 incorporates many of the security measures that protects a voltage drop, overheating or an overload .

The module Z-wave More FGS-223 allows you to set the thresholds higher and lower for energy consumption. Once the limit is exceeded, the module can notify you or automatically turn off the device.


  • Order two lights/appliances remotely

  • Installs behind existing switch

  • Function ON/OFF

  • Integrates the chip Z-Wave 500 series

  • Communication 250% faster compared to devices Z-Wave standard

  • Mechanism of activation of built-in scene

  • Classes of security communication and notification

  • Menu configuration with a diode

  • Measurement of the energy and the power of the connected devices

  • Supports the secure mode (the Security of the Z-Wave network) encrypted with encoding AES-128

  • Tester network coverage Z-Wave integrated

  • A software update OTA (depends on controller)

  • Terminal blocks for greater wiring convenience

  • Rounded shape to meet the most stringent standards

  • Use it goes and comes

  • Use in place of an energy supply trip-switch

  • Small, discrete and aesthetic

  • Ease of use and installation

  • Type of module : Receiver Z-Wave

  • Power supply : 100 - 240V~, 50/60Hz

  • Wiring : 3-wire, neutral required

  • Max power : 6.5 A per channel, 10A total (resistive load only)

  • Frequency : 868,42 Mhz

  • Transmission Distance : 50m free field, up to 40 m indoors

  • Signal power : 1mW

  • Dimensions: 42.5 mm x 38.25 to mm x 20.3 mm (L x w x h)

  • Operating temperature : 0-35°C

  • Standards :

    • EMC 2014/30/EU

    • RED 2014/53/EU

    • RoHS 2011/65/EU

    • LVD 2014/35/EU

The adapter Eutonomy euFIX S223 is used to install the module Fibaro® Switch FGS-223 on a rail of type DIN TH35 in the electrical panel.

The adapter Eutonomy euFIX S223 consists of a housing and an electronic card on which the module Switch FGS-223 is mounted.

The dimensions of the case are appropriate for a standard rail DIN TH35/TS35.

The e-card contains a set of screw terminals, where all the wires (power, signal input and output, command buttons) can be connected safely.

The front panel of the case contains two micro-buttons of diagnosis S1 and S2, which can be used to control the module, save the module in the Z-Wave system or remove it from the system without opening the housing of the adapter.

Features S223:

  • Adapter DIN to Fibaro Double Switch FGS-223 with push buttons

  • Used to install the module Fibaro Double Switch FGS-223-rail type DIN-TH35 / TS35 in the electrical panel

  • Location free on the label to identify the line controlled

  • Micro-push buttons S1 and S2 used for the control, the inclusion or exclusion of the module from the Z-Wave system

  • Supply voltage: 230 V AC +/- 10%, 50-60Hz

  • Power load: max 6.5 A per channel, 10A total

  • Dimensions: 34,8 x 87,3 x 64,7 mm

  • Width in units TE: 2 TE coolers

  • Cross Section of the conductor of wire : max. 2.5 mm2

  • Maximum length of the wires connected to the inputs Sx, S1, S2: 20m

  • Operating temperature: 0 ° C to +50 ° C

  • Relative humidity: ≤90%, no condensation

  • Guidelines:

    • LVD 2014/35 / EC

    • RoHS 2011/65 / EU

Pack content


No customer reviews for the moment.

Write a review

Fibaro FGS-223 - Fibaro module double switch Z-Wave Plus DIN-rail

Fibaro FGS-223 - Fibaro module double switch Z-Wave Plus DIN-rail

Fibaro FGS-223 module Z-Wave Plus DIN-rail

Customers who bought this product also bought: