Odroid N2+ - Single Board Computer N2 Plus 4 Gb RAM

The Odroid N2+ is perfect for installing Home Assistant and dominating your home

ODROID N2+ is a revision of ODROID-N2.

- The maximum CPU clock of Quad-core Cortex-A73 is increased to 2.4 Ghz from 1.8 Ghz.

- The maximum CPU clock of the dual-core Cortex-A53 is increased to 2.0 Ghz from 1.9 Ghz.

– The built-in RTC battery backup holder is mounted on the board.

The main processor is based on the big architecture. Little which integrates a cluster of quad-core ARM Cortex-A73 processors and a dual-core Cortex-A53 cluster with a next-generation Mali-G52 GPU.

Thanks to modern 12nm silicon technology, A73 cores operate at 2.2 GHz without thermal throttling using the original metal-cased heatsink for a rugged and quiet computer.

The multi-core performance of the CPU is about 20% faster and the GPU is 10% faster than the N1. The N2+'s DDR4 RAM runs at 1320MHz with a low power consumption of 1.2 volts.

The large metal-cased heatsink is designed to optimize CPU and RAM heat dissipation and minimize throttling. The CPU is placed on the underside of the PCB to establish large thermal characteristics.

Specifications Odroid N2+ - Single Board Computer N2 Plus 4 Gb RAM:

• Form factor card dimensions: 90 mm x 90 mm x 17 mm

• Heatsink dimensions: 100 mm x 91 mm x 18.75 mm

• Weight: 200 g with heatsink

• Amlogic S922X processor (12nm manufacturing)

• Quad-core Cortex-A73 (up to 2.4 GHz) and dual-core Cortex-A53 (up to 2 GHz)

• ARMv8-A architecture with Neon and Crypto extensions

• Mali-G52 GPU with 6 x runtime engines (800Mhz)

• 4GB or 2GB DDR4 memory with 32-bit bus width

• Data rate: 2640 MT/s (grade PC4-21333)

• Low-power design of 1.2 volts

• Storage

  • 1 x eMMC connector (8G, 16G, 32G, 64G and 128G are available)

  • 1 microSD slot (DS/HS modes up to UHS-I SDR104)

• Networking

  • 1 x GbE LAN ports (RJ45, supports 10/100/1000Mbps)

  • Realtek RTL8211F (Ethernet transceiver)

• LED indicators

  • * Green LED: Flashing by data traffic at a 100 Mbps connection

  • * Orange LED: flashing by data traffic at a 1,000 Mbps connection

• Optional USB Wi-Fi adapters

• Video

  • 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)

  • 1 x Composite video (3.5mm jack)

• Audio

  • 1 x Stereo Audio Output (3.5mm jack)

  • 1 HDMI digital output

  • 1 x Optional SPDIF optical output

• External I/O 4 USB 3.0 host ports (sharing a single root hub)

• 1 USB 2.0 OTG port for host or device mode. (No power input)

• 1 x Serial Debug Console (UART)

• 1 x Peripheral expansion connector (40-pin, 2.54mm pitch)

• 2 x DC 5V, 2 x DC 3.3V, 1 x DC 1.8V, 8 x GND

• 1 x SPI

• 1 UART

• 2 x I2C

• 25x GPIO (Max)

• 2 ADC inputs (10bit, 1.8V Max)

• All 3.3V I/O signal levels, except for ADC input at 1.8 Volt max.

• Other features IC RTC (Real Time Clock) built-in to keep date and time. A CR2032 coin cell battery holder has been replaced by the 2-pin 1.25mm pitch connector.

• No batteries are included in the card.

• Please purchase the very common CR2032 naked cell from your local store.

• You can save RTC time for up to several years with a 200mAh CR2032 battery.

• 8 MB SPI Flash for Boot Manager

• IR receiver for remote control

• Built with a large passive heatsink

• System LED indicators:

• Red (PWR) – Turned on when DC power is connected

ALIVE - Blinking like a heartbeat while the kernel is running.

Active cooling fan connector (5V 2-pin)

Connector (2-pin, 1.25mm pitch)

Power supply 1 x DC socket: outer diameter (negative) 5.5 mm, inner diameter (positive) 2.1 mm

DC 7.5V~18V (up to 25W) ***7.5V~16V from 2022 production (BATCH number starts with EL22)

A DC 12V/2A AC adapter is recommended

Power consumption:

• IDLE: ≃ 2.2W (Performance Governor)

• CPU demand: ≃ 5.9W (@2016/2208MHz), 6.2W (@2016/2400MHz)

• Power off: ≃ 0.2W